|
|
@@ -0,0 +1,63 @@
|
|
|
+
|
|
|
+
|
|
|
+X<RR>
|
|
|
+
|
|
|
+ Enable data reporting for SlowRF (i.e. 1kHz data rate)
|
|
|
+ <RR> is a one-byte hex value, with following bits (bit 0 is the LSB bit):
|
|
|
+ Bit 0: Report known messages (parity & checksum ok), with type prefix.
|
|
|
+ Bit 1: Report each of the (repeated) packets of a message
|
|
|
+ Bit 2: Report detailed data, even with wrong parity / checksum.
|
|
|
+ Bit 3: Monitor mode: output an r on a risings edge and 'f' on a falling edge. Output a '.' at the end of the message (no signal for 4msec).
|
|
|
+ Bit 4: Timing: in monitor mode output one additional byte of the internal microsecond timer, divided by 16. This is binary!
|
|
|
+ Bit 5: RSSI: report RSSI value as an additional HEX byte after digested data or as a separate byte if Bit 3 is set too.
|
|
|
+ Bit 6: Report FHT protocol messages (ack, etc)
|
|
|
+ Bit 7: CUL/CUN: Report raw RSSI data (a==weak ... p==strong signal) CUR: Grafic representation: dark==weak ... light == stong signal
|
|
|
+
|
|
|
+ Note: 00 disables radio reception, any other value initializes the radio chip and enables reception. Default is 00: do not report anything, radio chip is uninitialized.
|
|
|
+ Example: X01 (normal reporting, no RSSI) or X67 (debugging)
|
|
|
+
|
|
|
+ If <RR> is not specified, report the current value and the available time for sending RF (in 10 ms units)
|
|
|
+
|
|
|
+
|
|
|
+
|
|
|
+X67 = 01100111
|
|
|
+ Bit 0: Report known messages (parity & checksum ok), with type prefix.
|
|
|
+ Bit 1: Report each of the (repeated) packets of a message
|
|
|
+ Bit 2: Report detailed data, even with wrong parity / checksum.
|
|
|
+ # Bit 3: Monitor mode: output an r on a risings edge and 'f' on a falling edge. Output a '.' at the end of the message (no signal for 4msec).
|
|
|
+ # Bit 4: Timing: in monitor mode output one additional byte of the internal microsecond timer, divided by 16. This is binary!
|
|
|
+ Bit 5: RSSI: report RSSI value as an additional HEX byte after digested data or as a separate byte if Bit 3 is set too.
|
|
|
+ Bit 6: Report FHT protocol messages (ack, etc)
|
|
|
+ # Bit 7: CUL/CUN: Report raw RSSI data (a==weak ... p==strong signal) CUR: Grafic representation: dark==weak ... light == stong signal
|
|
|
+
|
|
|
+X21 = 00100001
|
|
|
+ Bit 0: Report known messages (parity & checksum ok), with type prefix.
|
|
|
+ # Bit 1: Report each of the (repeated) packets of a message
|
|
|
+ # Bit 2: Report detailed data, even with wrong parity / checksum.
|
|
|
+ # Bit 3: Monitor mode: output an r on a risings edge and 'f' on a falling edge. Output a '.' at the end of the message (no signal for 4msec).
|
|
|
+ # Bit 4: Timing: in monitor mode output one additional byte of the internal microsecond timer, divided by 16. This is binary!
|
|
|
+ Bit 5: RSSI: report RSSI value as an additional HEX byte after digested data or as a separate byte if Bit 3 is set too.
|
|
|
+ # Bit 6: Report FHT protocol messages (ack, etc)
|
|
|
+ # Bit 7: CUL/CUN: Report raw RSSI data (a==weak ... p==strong signal) CUR: Grafic representation: dark==weak ... light == stong signal
|
|
|
+
|
|
|
+X05 = 00000101
|
|
|
+ Bit 0: Report known messages (parity & checksum ok), with type prefix.
|
|
|
+ # Bit 1: Report each of the (repeated) packets of a message
|
|
|
+ Bit 2: Report detailed data, even with wrong parity / checksum.
|
|
|
+ # Bit 3: Monitor mode: output an r on a risings edge and 'f' on a falling edge. Output a '.' at the end of the message (no signal for 4msec).
|
|
|
+ # Bit 4: Timing: in monitor mode output one additional byte of the internal microsecond timer, divided by 16. This is binary!
|
|
|
+ # Bit 5: RSSI: report RSSI value as an additional HEX byte after digested data or as a separate byte if Bit 3 is set too.
|
|
|
+ # Bit 6: Report FHT protocol messages (ack, etc)
|
|
|
+ # Bit 7: CUL/CUN: Report raw RSSI data (a==weak ... p==strong signal) CUR: Grafic representation: dark==weak ... light == stong signal
|
|
|
+
|
|
|
+X01 = 00000001
|
|
|
+ Bit 0: Report known messages (parity & checksum ok), with type prefix.
|
|
|
+ # Bit 1: Report each of the (repeated) packets of a message
|
|
|
+ # Bit 2: Report detailed data, even with wrong parity / checksum.
|
|
|
+ # Bit 3: Monitor mode: output an r on a risings edge and 'f' on a falling edge. Output a '.' at the end of the message (no signal for 4msec).
|
|
|
+ # Bit 4: Timing: in monitor mode output one additional byte of the internal microsecond timer, divided by 16. This is binary!
|
|
|
+ # Bit 5: RSSI: report RSSI value as an additional HEX byte after digested data or as a separate byte if Bit 3 is set too.
|
|
|
+ # Bit 6: Report FHT protocol messages (ack, etc)
|
|
|
+ # Bit 7: CUL/CUN: Report raw RSSI data (a==weak ... p==strong signal) CUR: Grafic representation: dark==weak ... light == stong signal
|
|
|
+
|
|
|
+
|
